| Make | Model | Problem | Solution | Added | Date |
| | | | |
| Found: 4551 |
| Philips | ANUBIS-S | Mains fuse 1500 fails constantly | In case the mains fuse of a 25" Anubis S BB set constantly blows,
it is recommended to upgrade it to a 4A type:
Change fuse 1500 to T4A 4822 070 34002
Also update the text T3.15A on the service printing to a
sticker with the text T4A.
REMARKS | plamensl | 14-09-2004 |
| Philips | ANUBIS-S | Modification | Modification
------------
For ALL ANUBIS-S WITH NO SECAM RECEPTION
IC7225 TDA8362 is replaced by TDA8361 in all ANUBIS-S sets with
no SECAM reception possibility from production week 9416 onwards,
so,
IC7225 = TDA 8361E/N3 4822 209 33479 (PAL + NTSC, n | plamensl | 14-09-2004 |
| Philips | ANUBIS-S | No +95V/+115V from power supply | In case of a failure of one of the components TS7513, R3503 or
D6502 till D6505, it is strongly recommended to replace all of
these components.
For service codes see,
Service Manual ANUBIS-S AA
GB 4822 727 19707
E 4822 727 19719
ANUBIS-S BB
| plamensl | 14-09-2004 |
| Philips | ANUBIS-S | No colour at PAL in case of disconnected 2CS+I/O+Ampl panel | In the service position, the main panel of the Anubis S BB is
disconnected from the 2CS+I/O+Amplifiaction panel.
For Anubis S BB sets with 2 HEF shift register in cascade (as how
it is used by now for controlling an Anubis S BB set with
incredible stere | plamensl | 14-09-2004 |
| Philips | ANUBIS-S | No NICAM sound | In case of no NICAM sound it is recommended to replace on the NICAM
panel:
R3055 to 560 ohm 2% 0.25W 4822 051 10561
(diagram K page 21 in the service manual
Anubis S BB 4822 727 20262)
REMARKS :
Lower R3055 gives a higher starting current fo | plamensl | 14-09-2004 |
| Philips | ANUBIS-S | No picture | Apply a slight force to further insert the EHT cable into the line
output transformer 5445.
REMARKS :
Above cure is only relevant for sets with LOT 4822 140 10525
or 4822 140 10557.
When replacing the above mentioned LOT's, please take note of t | plamensl | 14-09-2004 |
| Philips | ANUBIS-S | No picture after picture tube flash over | In case after a picture tube flash over (one of) the video output
transistor(s) BF422 (TS7305, TS7318, TS7327) failed, it is
recommended to:
1. Change 2337 to 4n7 2kV 4822 126 12833
2. Delete and short R3336 with a wire jumper
3 | plamensl | 14-09-2004 |
| Philips | ANUBIS-S | No stereo, no +95 volt | R3523 is interrupted, D6519 and C2519 (= capacitor between D and
S-7513) are short circuited.
Remove C2519. Replace R3523 - 390K - 4822 116 52278
Replace D6519 - BTZ03-C15 - 5322 130 31574
| plamensl | 14-09-2004 |
| Philips | ANUBIS-S | One colour missing or no picture | In case of 1 colour missing or no picture, it is recommended
to solder across R3301 on the CRT panel on the copper side:
100nF 10% 250V 4822 121 41689
This capacitor protects the 3 BF422 video output transistors
TS7305, 7318 and 7327 against flash
REM | plamensl | 14-09-2004 |
| Philips | ANUBIS-S | Only for ANUBIS-S BB 25
Adaption in the frame par | Only for ANUBIS-S BB 25
Adaption in the frame part of 25" Anubis S BB
---------------------------------------------
From production start onwards the following modification is done in
the convergence circuitry in the frame part of diagram AA:
R3403 shou | plamensl | 14-09-2004 |
| Philips | ANUBIS-S | Only for ANUBIS-S BB 25" Codenumber information | Only for ANUBIS-S BB 25"
Codenumber information
----------------------
The missing service codenumber for the bridge coil L5480 in the
east / west part of the 25" ANUBIS S BB (diagram AA) is:
4822 157 71149
| plamensl | 14-09-2004 |
| Philips | ANUBIS-S | OSD characters too thin | It is recommended to replace in the control part:
R3715 by 1k2 (4822 116 52207)
REMARKS :
Introduced in production week 9408
| plamensl | 14-09-2004 |
| Philips | ANUBIS-S | Picture jittering when OSD is recalled, all versions | Replace R3605 by 2k (4822 116 52253) at pin 20 of uP
REMARKS :
Introduced in production week 9328
| plamensl | 14-09-2004 |
| Philips | ANUBIS-S | Picture tube 20" Anubis S AA and CC A48KXR98X | Picture tube 20" Anubis S AA and CC A48KXR98X (4822 131 20577)
---------------------------------------------------------------
Only for ANUBIS-S 20" AA and CC
For both Anubis S AA and CC picture tube A48KXR98X (neutral
hemisphere) is no longer available | plamensl | 14-09-2004 |
| Philips | ANUBIS-S | Picture width too small during off-air reception. | Delete R3453, R3454 and L5454 in the line defl flyback circuitry
and place jumper at position 9454.
REMARKS :
Introduced in production week 9340 in Spore and week 9346 in LFL
Thailand.
| plamensl | 14-09-2004 |
| Philips | ANUBIS-S | Pix blanks at certain prog. nrs | Software bug.
Micro Processor need to be replaced.
Change from version SA FHV 1.9 to SA FHV 2.1
| plamensl | 14-09-2004 |
| Philips | ANUBIS-S | Plop at switching on/off NICAM sound | In case of a NICAM switch on/off plop it is recommended to change
on the NICAM module (diagram K) of the Anubis S BB:
* Place elco 47uF 20% 25V (4822 124 40433) with + to pin 9 of
IC7075 and with - to ground
* Replace C2065 and C2076 by 470nF 10% 50V ( | plamensl | 14-09-2004 |
| Philips | ANUBIS-S | Plop at switching on/off NICAM sound | In case of a NICAM switch on/off plop it is recommended to change
on the NICAM module (diagram K) of the Anubis S BB:
* Place elco 47uF 20% 25V (4822 124 40433) with + to pin 9 of
IC7075 and with - to ground
* Replace C2065 and C2076 by 470nF 10% 50V ( | plamensl | 14-09-2004 |
| Philips | ANUBIS-S | Plop sound at switch off of the set | For mono versions:
Replace D6109 by BZX79-C2V7 (5322 130 34563)
For stereo PB (+ BTSC) versions:
Replace D6807 and D6808 by LLZ-C2V7 (4822 130 81138)
REMARKS :
Introduced in production week 9331
| plamensl | 14-09-2004 |
| Philips | ANUBIS-S | Powers supply output voltages for the different sc | Powers supply output voltages for the different screensizes
for ANUBIS-S AA/BB/CC/DD
------------------------
For adjusting the power supply output voltage (via R3512) following
survey gives an overview of the values for the different screensizes
of all c | plamensl | 14-09-2004 |