| Make | Model | Problem | Solution | Added | Date |
| | | | |
| Found: 4551 |
| Philips | 29PT6231 | Interference from adjacent channel | Check, and replace/change posn: 1145 (SAW filter)
on chassis to 2422 549 44223 OFWK7260M
For /79R, add posn: 1168, 4822 242 81572 6MHz
ceramic filter
REMARKS :
Solution implemented in production | plamensl | 14-09-2004 |
| Philips | 29PT828C | STUCK IN STANDBY | RESOLDER SCAN COIL PLUGS | plamensl | 14-09-2004 |
| Philips | 29PT828C | TRIPS FROM GREEN LED TO RED TO GREEN TO RED | REPLACE IC7450, AND IC7550 ON AUDIO PCB | plamensl | 14-09-2004 |
| Philips | 29PT8319 | Corrections on service manual EM1A AA | Page 4 Chapter 2:
It was forgotten to mention here in this chapter that the architecture is 'hot'for a big part.
E,g. deflection is 'hot', but also the middle big heatsink. So be warned.
Page 16 Chapter 5:
SAM-menu on right hand top side, sho | plamensl | 14-09-2004 |
| Philips | 29PT8419 | Corrections on service manual EM1A AA | Page 4 Chapter 2:
It was forgotten to mention here in this chapter that the architecture is 'hot'for a big part.
E,g. deflection is 'hot', but also the middle big heatsink. So be warned.
Page 16 Chapter 5:
SAM-menu on right hand top side, sho | plamensl | 14-09-2004 |
| Philips | 29PT8424 | Correction to position 21 of styling 220 | Correction to position 21 of styling 220 of Product Survey 1999-3 (3122
785 10300
The code numbers mentioned for the aluminium columns at position 21 of
styling 220 are not correct. The correct code numbers must be:
21 4822 466 12216 Aluminium colum | plamensl | 14-09-2004 |
| Philips | 29PT8434 | Correction to position 21 of styling 220 | Correction to position 21 of styling 220 of Product Survey 1999-3 (3122
785 10300
The code numbers mentioned for the aluminium columns at position 21 of
styling 220 are not correct. The correct code numbers must be:
21 4822 466 12216 Aluminium colum | plamensl | 14-09-2004 |
| Philips | 29PT8444 | Correction to position 21 of styling 220 | Correction to position 21 of styling 220 of Product Survey 1999-3 (3122
785 10300
The code numbers mentioned for the aluminium columns at position 21 of
styling 220 are not correct. The correct code numbers must be:
21 4822 466 12216 Aluminium colum | plamensl | 14-09-2004 |
| Philips | 29PT9113C | WHITE BOX BOTTOM LEFT OF SCREEN | AUTO SUBTITLE SELECTED SWITCH OFF FROM HANDSET | plamensl | 14-09-2004 |
| Philips | 29PT9416 MG7.1 | Service Mode entering | Use the standard remote control and key in a special sequence '0,6,2,5,9,6' followed by pressing the 'MENU' button. If the main menu also appears with the service menu just press 'MENU' again to clear it.. The other way is to short the two service pins on the signal panel (pins 2 and 3 of connector 0356). The advantage of this last method is that all the software protections are turned off. | plamensl | 14-09-2004 |
| Philips | 29PW6332/05 | NO TEXT, NO DOLBY OR ZOOM FEATURES NOT WORKING | RESET OPTIONS USING SERVICE TOOL PRESS "ALIGN" A MENU APPEARS RESET RELEVENT OPTIONS FROM "N" TO "Y" | plamensl | 14-09-2004 |
| Philips | 2A | 140V voltage is 120V. Stand-by and EXT1 LEDs are on. | Diode 6663 (1N5062; 4822 130 41275) short-circuited, IC7830
(MAB8441P/T001; 4822 209 11037) defective.
REMARKS :
Only for sets with CITAC module.
| plamensl | 14-09-2004 |
| Philips | 2A | After flashover of picture tube, set is in protection mode. | Set works again after turning on and off.
Solution:
Connect a 100 Ohm resistor (4822 116 52175) between gate of D6698
and junction R3698/C2698. | plamensl | 14-09-2004 |
| Philips | 2A | Bars in picture. | 199V on collector TS7422. (has to be 193V).
R3427 (300k; 4822 116 52268) defective (for green)
R3407 (300k; 4822 116 52268) defective (for red)
R3447 (300k; 4822 116 52268) defective (for blue) | plamensl | 14-09-2004 |
| Philips | 2A | BLACK LINES ON PIC , LIKE EVERY OTHER LINE MISSING | C2050 47mfd , 50v IN IF. CAN | plamensl | 14-09-2004 |
| Philips | 2A | Blank raster & no sound. | Memory back-up batt. | plamensl | 14-09-2004 |
| Philips | 2A | Blowing BUT11A - may last days. | Change chopper transformer ( will look ok ) | plamensl | 14-09-2004 |
| Philips | 2A | Blowing T7618. | Drys on T5632 ( LOP drive TX ) | plamensl | 14-09-2004 |
| Philips | 2A | BRIGHT PIC + FLYBACK LINES | R3473 910k OC | plamensl | 14-09-2004 |
| Philips | 2A | BUT11 SC. | CHECK THAT L5687 IS STILL INTACT ( IN SERIES WITH BUT11 BASE ) | plamensl | 14-09-2004 |