| Make | Model | Problem | Solution | Added | Date |
| | | | |
| Found: 4551 |
| Philips | 14PV330 | Dead | D6391 BYW98/200 in psu s/c | plamensl | 14-09-2004 |
| Philips | 14PV345/05 TVCR99 | Dead at start up with Rec LED flashing | Sus EEPROM IC7818 on video board | plamensl | 14-09-2004 |
| Philips | 14PV345/05 TVCR99 | No pic TV or Pback - sound, OSD & Txt ok | Painter IC SAA5562 was not sending correct info to TDA8841 jungle chip pin 26 - SAA chip faulty | plamensl | 14-09-2004 |
| Philips | 14PV461 | Codenumber information | The codenumber for the spacer between on/off switch and the knob (pos 3) is 4822 402 10702 | plamensl | 14-09-2004 |
| Philips | 14RGR1 | Removing Hotel Mode | press control + & - on ch38 | plamensl | 14-09-2004 |
| Philips | 14TV240/05 | No pic - sound ok | HT correct, no line drive; 3584 47R o/c | plamensl | 14-09-2004 |
| Philips | 14TV240/05 | Pic missing - sound ok | No line dr - Q7584 BC637-16 o/c or R3584 47R o/c or D6581 (use 1N4148) leaky | plamensl | 14-09-2004 |
| Philips | 14TVCR240 | Codenumber correction | The codenumber (4835 310 57339) in the Service Manual (see page 1-2-19) for the extension PCB of the mechanism, is wrong.The correct codenumber is 4822 321 62609. | plamensl | 14-09-2004 |
| Philips | 14TVCR240 | Codenumber information | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271.
This new version is only used in the following sets:
14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05, 14PV163/05H, 14PV263/01, | plamensl | 14-09-2004 |
| Philips | 14TVCR240 | Correction partslist | In the partslist, 17.734 MHz is mentioned for X-tal pos.1200. This has to be 4.43 MHz. The codenumber 4822 242 81809 is correct. Also the specifications of the X-tal on the circuit diagramm on page 1-3-7 is correct. | plamensl | 14-09-2004 |
| Philips | 14TVCR240 | Damages tapes; eject of cassette with difficulty. | Replace kit I (4822 310 31963).
| plamensl | 14-09-2004 |
| Philips | 14TVCR240 | Dead | Check start up volts pin 6 TDA4605 should be 10v; if low at 3v check UG06B diode D6334 for leak (pt no 4822 130 83307) | plamensl | 14-09-2004 |
| Philips | 14TVCR240 | Dead | D6581 - used By133 in lieu | plamensl | 14-09-2004 |
| Philips | 14TVCR240 | Dead with blurting noise | LOPTx s/c CHS code no P81397 | plamensl | 14-09-2004 |
| Philips | 14TVCR240 | dead, PSU not running | D6334 UG06B leaky (482213083307) | plamensl | 14-09-2004 |
| Philips | 14TVCR240 | Field collapse | TDA3653 replaced | plamensl | 14-09-2004 |
| Philips | 14TVCR240 | How to erase memory | Press simultanuously buttons REWIND, WIND and PROGRAMM (<<, >> and P-) while switching on the power supply.
Note: Correct your service manual on page 1-1-11.
The description in the Instruction For Use is correct. | plamensl | 14-09-2004 |
| Philips | 14TVCR240 | Key set | The key set assy has been codified for all B-range TVCR's. This will allow to change the keys without having to change the complete frame. Servicenr. 4822 410 11069.
Key set for: 14PV162/01/02/05/07/08/13/58 - 14PV170/05 - 14TVCR240/01N. | plamensl | 14-09-2004 |
| Philips | 14TVCR240 | Memory erase procedure | The contents of the memory can only be cleared via the service mode. This option is not available for end users. (Risc of destroying option codes).
Service mode: press "STOP" on Remote Control and "PLAY" on the set for 5 seconds. Select the second page | plamensl | 14-09-2004 |
| Philips | 14TVCR240 | Modification picture tube | From production week 9610 onwards, an ORION picture tube was mounted. The codenumber was 4822 131 11075.
Together with this picture tube capacitor C2586 has been changed to 8 nF - 1600 V. Codenumber 4822 121 70629.
For replacement ORION picture tube by | plamensl | 14-09-2004 |