| Make | Model | Problem | Solution | Added | Date |
| | | | |
| Found: 4551 |
| Philips | 14PV162 | Codenumber correction | The codenumber of pos. 1701 (tuner) for 14 inch sets with IEC input is 4822 210 10691 (UV916S). | plamensl | 14-09-2004 |
| Philips | 14PV162 | Codenumber correction for deck-up (IC7410) | The codenumber for the deckprocessor was wrong in the first Service Manual (4822 726 15451).
In service information TVCR96-01 and in the new manual the correct codenumber is given.
The codenumber for the deck-up for sets with non-turbo drive is: 4822 | plamensl | 14-09-2004 |
| Philips | 14PV162 | Codenumber information | Please add following codenumbers to the Service Manual:
Lift-flap 14PV162/01 : 4822 443 10402
Lift-flap 14PV162/02 : 4822 443 10402
Spring for lift-flap : 4822 492 70896 | plamensl | 14-09-2004 |
| Philips | 14PV162 | Codenumber information | The codenumber for the spacer between on/off switch and the knob (pos 3) is 4822 402 10702. | plamensl | 14-09-2004 |
| Philips | 14PV162 | Key set | The key set assy has been codified for all B-range TVCR's.
This will allow to change the keys without having to change the complete frame.
Servicenr. 4822 410 11069 - Key set for: 14PV162/01/02/05/07/08/13/58 - 14PV170/05 - 14TVCR240/01N. | plamensl | 14-09-2004 |
| Philips | 14PV162 | Memory erase procedure | The contents of the memory can only be cleared via the service mode. This option is not available for end users. (Risc of destroying option codes).
Service mode: press "STOP" on Remote Control and "PLAY" on the set for 5 seconds. Select the second page | plamensl | 14-09-2004 |
| Philips | 14PV162 | Modification | From week 9644 onwards, the following modifications are done on the Small Signal Board:
2076 / 470pF 5% is DELETED.
3075 / 33k 5% is DELETED.
4999 / CHIP JUMPER / 4822 051 20008 is inserted in place of 2076.
The RC differentiator was not necessary whe | plamensl | 14-09-2004 |
| Philips | 14PV162 | Preventive tip | If FET 7352 is found to be defective, it is advised to mount a 15 V zenerdiode (BZX79-C15) between the drain and the gate.
Mount cathode to gate and anode to drain.
Codenumbers:
FET 7352: 4822 130 60838
ZENER (BZX79-C15): 4822 13034281
Introduc | plamensl | 14-09-2004 |
| Philips | 14PV162 | Set produces audible noise in stand-by | Add a small LEBL (leading edge blanking) PCB, to avoid auto oscillation of transformer 5330 (or 5331). A modification letter is included with the lable PCB. This PCB is available with service nr. 4822 214 12173.
Since production week 9723 this circuit is | plamensl | 14-09-2004 |
| Philips | 14PV162 | Spare part information | A repair kit , containing PULLEY SHAFT + WORM SHAFT (POS. 47+48) is delivered with codenumber 4822 310 10657.
This kit can be used for all TURBO- and ECO mechanisms ! | plamensl | 14-09-2004 |
| Philips | 14PV162 | Spare part information | If the lever inside the mains-switch is broken, the switch doesn't remain in the "ON" position.
Solution: replace the switch by a new one. Improved switches of a newer production range are on stock. (4822 276 13542) | plamensl | 14-09-2004 |
| Philips | 14PV162 | Start up problems | When the set is switched on by the mains-switch while a cassette is in the set, the front LED starts blinking, but the set doesn't start.
Solution:
Check the primary voltage (Ubat) and adjust this for 14" sets to exactly 101.5 Volt. (See chapter 3.1.1 | plamensl | 14-09-2004 |
| Philips | 14PV162 | Tuner modification | An early production problem appears on these sets: the AGC voltage supplied to the Tuner 1 is too high (app. 8.8V) in comparison to the supply voltage (5V). It results in a wrong correction of the AGC loop when the antenna's signal is too low (about 1,5mV | plamensl | 14-09-2004 |
| Philips | 14PV162/01 | Codenumber information | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271.
This new version is only used in the following sets:
14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05,
14PV163/05H, 14PV263/01 | plamensl | 14-09-2004 |
| Philips | 14PV162/01 | Option code: 00396 | From week 02/97 onwards the option code is printed on the typesticker. Always use this code ! For early sets without this information on the typesticker, the option code is: 00396 | plamensl | 14-09-2004 |
| Philips | 14PV162/02 | New VPS IC SDA5642-6 (pos. 7840) | Since production week 9741 a new VPS IC pos. 7840 (SDA5642-6) is introduced in production.
This IC is not compatible with the previous one. When ordering, look at the printing on the IC !
Old: SDA 5642-5 - codenumber 4822 209 32728
New: SDA 5642-6 - | plamensl | 14-09-2004 |
| Philips | 14PV162/02 | Option code: 00972 | From week 02/97 onwards the option code is printed on the typesticker. Always use this code !
For early sets without this information on the typesticker, the option code is: 00972 | plamensl | 14-09-2004 |
| Philips | 14PV162/05 | Codenumber information | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271.
This new version is only used in the following sets:
14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05,
14PV163/05H, 14PV263/01 | plamensl | 14-09-2004 |
| Philips | 14PV162/07 | Codenumber information | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271.
This new version is only used in the following sets:
14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05,
14PV163/05H, 14PV263/01 | plamensl | 14-09-2004 |
| Philips | 14PV163 | Codenumber information | The codenumber for the spacer between on/off switch and the knob (pos 3) is 4822 402 10702. | plamensl | 14-09-2004 |