Schematics 4 Free
Service manuals, schematics, documentation, programs, electronics, hobby ....
◦
register
◦
send pass
S
earch
B
rowse
U
pload
W
anted
D
atasheets
C
hassis2model
R
epair tips
F
ulltext search
C
ables & Connectors
R
epair tips
Electronic appliance repair tips database - TV (LCD,TFT,Plasma,Digital), Monitor, VCR, DVD recorder and player, Digital camera, Audio equipment, Microwave ovens, Phone systems, Computer repair
Make
Model
Problem
Solution
Date
Found: 534
Grundig
GSC100
Dead.
Di511 or C2502 ( 100u f , 16v ) on EHT control regel baust PCB.
14-09-04
Grundig
GSC100
Frame - bottom foldover - cramping at top.
R2522 ( 2.2k ) goes high.
14-09-04
Grundig
GSC100
IF EHT IS VERY HIGH
CHECK DI508 IS OPEN
14-09-04
Grundig
GSC100
Line break up.
C2502 ( 100uf , 16v ) on EHT control regel baust PCB.
14-09-04
Grundig
GSC100
No frame.
Di447 ( 1N4007 ) and/or TDA1170.
14-09-04
Grundig
GSC100
R607 - repeated resoldering of R607.
Di2502 ( 4.7v ) zener.
14-09-04
Grundig
GSC200
No results.
R607 o/c , R621 o/c , if goes agn few hrs later Di2502 4.7v
14-09-04
Grundig
GSC200 Chassis
Arcing in picture. Reduced width with torn edges.
The HO Transformer has a built in fuse holder which houses a 50mA fuse. (connected in series with the high tension cable). Replace the fuse and clean the contacts.
14-09-04
Grundig
GSC200 Chassis
Black screen, EHT at about 18 KVs.
Change Di511.
14-09-04
Grundig
GSC200 Chassis
No sound or Picture, led displays not lit.EHT at 18KV.
C2607 in relay PCB Sced.Check also D334 and D335 in tuning module as in one case they were found to be Sced together with C2607.
14-09-04
Grundig
GSC700
Int smeary flat picture.
Luma delay line leaky.
14-09-04
Grundig
GT1401
No sound or pic
5v supply missing because D114 cathode no soldered thro' print
14-09-04
Grundig
GT2103
Hum bar
mains smoother 47µ 385v o/c
14-09-04
Grundig
GT2105
Bright white raster
R315 10R on crt base o/c
14-09-04
Grundig
GT2105
Dead - HT pulsating
Tr302 LOPTr s/c
14-09-04
Grundig
GT2105
Dead - no line drive
R315 o/c
14-09-04
Grundig
GT2105
No Green
R908 on crt base & R802 near RGB chip
14-09-04
Grundig
GT2105
Unstable pic & sound
33v tuner supply fluctuating at 25v - tuner faulty
14-09-04
Grundig
M82-100IDTV
Tripping - stops if tripler dis'd
Check caps in psu control sub panel for low capacitance
14-09-04
Grundig
M82-102IDTV
Int cuts out
Chopper trfmr breaking down
14-09-04
Grundig
MW70-3699
Dead 1.6A fuse blown
Check 270k res for o/c behind chopper Tr & replace chopper Tr
14-09-04
Grundig
MW82-2700 CUC2058
Dead - pri volts only
R60002 (680K 1W) was O/C situated just behind the switch mode MOSFET on the primary side.
14-09-04
Grundig
P37-440
Sound - random volume up & down.
IR IC TFMS3300 or 4300 with metal screen over it.
14-09-04
Grundig
P37-440
Tuning - random channel change.
IR IC TFMS3300 or 4300 with metal screen over it.
14-09-04
Grundig
P45-440/1GB
No pic - sound ok - faint arcing noise
dry joints ww res R516 in line stage
14-09-04
Grundig
SE7086TOP etc
int no sound - when increased gives popping noise
Mains sw st/by contacts int
14-09-04
Grundig
ST 70-755
Grundig ST 70-755 TOP/LOG. Picture quality is great and TV turns on fine and displays picture fine for 1 - 2 hours. Then screen starts quick, short burts of flicker / flashes. (Picture can always be seen durring these flickers but is very anoying and ob
Check electroylitics round frame output i.c. some of them are low in capacity
24-06-05
Grundig
ST1772/9TOP
Field foldover
TDA8350Q chip
14-09-04
Grundig
st63-650
There is a white strip in middle on picture.
This means then the stage of frame is fault, You should check: - is there voltage of power on this part - IC of frame (probably TDA 2653 or TDA3654 ) - joins among main board and deflection coils - the deflection coils
12-12-05
Grundig
ST63460
Dim blank raster - no picture.
D2334 ( TD190 ) leaky.
14-09-04
page:
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
FB
-
Links
-
Info / Contacts
-
Forum
-
Last SM download : SMD Code`s smd codebook 2004 708
script execution: 0.14 s